Filtered by vendor Linux
Subscribe
Total
10566 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2024-56721 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: x86/CPU/AMD: Terminate the erratum_1386_microcode array The erratum_1386_microcode array requires an empty entry at the end. Otherwise x86_match_cpu_with_stepping() will continue iterate the array after it ended. Add an empty entry to erratum_1386_microcode to its end. | |||||
| CVE-2024-56722 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix cpu stuck caused by printings during reset During reset, cmd to destroy resources such as qp, cq, and mr may fail, and error logs will be printed. When a large number of resources are destroyed, there will be lots of printings, and it may lead to a cpu stuck. Delete some unnecessary printings and replace other printing functions in these paths with the ratelimited version. | |||||
| CVE-2024-56724 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: mfd: intel_soc_pmic_bxtwc: Use IRQ domain for TMU device While design wise the idea of converting the driver to use the hierarchy of the IRQ chips is correct, the implementation has (inherited) flaws. This was unveiled when platform_get_irq() had started WARN() on IRQ 0 that is supposed to be a Linux IRQ number (also known as vIRQ). Rework the driver to respect IRQ domain when creating each MFD device separately, as the domain is not the same for all of them. | |||||
| CVE-2024-56723 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: mfd: intel_soc_pmic_bxtwc: Use IRQ domain for PMIC devices While design wise the idea of converting the driver to use the hierarchy of the IRQ chips is correct, the implementation has (inherited) flaws. This was unveiled when platform_get_irq() had started WARN() on IRQ 0 that is supposed to be a Linux IRQ number (also known as vIRQ). Rework the driver to respect IRQ domain when creating each MFD device separately, as the domain is not the same for all of them. | |||||
| CVE-2024-56725 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: octeontx2-pf: handle otx2_mbox_get_rsp errors in otx2_dcbnl.c Add error pointer check after calling otx2_mbox_get_rsp(). | |||||
| CVE-2022-49035 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: media: s5p_cec: limit msg.len to CEC_MAX_MSG_SIZE I expect that the hardware will have limited this to 16, but just in case it hasn't, check for this corner case. | |||||
| CVE-2023-52485 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Wake DMCUB before sending a command [Why] We can hang in place trying to send commands when the DMCUB isn't powered on. [How] For functions that execute within a DC context or DC lock we can wrap the direct calls to dm_execute_dmub_cmd/list with code that exits idle power optimizations and reallows once we're done with the command submission on success. For DM direct submissions the DM will need to manage the enter/exit sequencing manually. We cannot invoke a DMCUB command directly within the DM execution helper or we can deadlock. | |||||
| CVE-2023-52497 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 6.1 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: erofs: fix lz4 inplace decompression Currently EROFS can map another compressed buffer for inplace decompression, that was used to handle the cases that some pages of compressed data are actually not in-place I/O. However, like most simple LZ77 algorithms, LZ4 expects the compressed data is arranged at the end of the decompressed buffer and it explicitly uses memmove() to handle overlapping: __________________________________________________________ |_ direction of decompression --> ____ |_ compressed data _| Although EROFS arranges compressed data like this, it typically maps two individual virtual buffers so the relative order is uncertain. Previously, it was hardly observed since LZ4 only uses memmove() for short overlapped literals and x86/arm64 memmove implementations seem to completely cover it up and they don't have this issue. Juhyung reported that EROFS data corruption can be found on a new Intel x86 processor. After some analysis, it seems that recent x86 processors with the new FSRM feature expose this issue with "rep movsb". Let's strictly use the decompressed buffer for lz4 inplace decompression for now. Later, as an useful improvement, we could try to tie up these two buffers together in the correct order. | |||||
| CVE-2024-56719 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: net: stmmac: fix TSO DMA API usage causing oops Commit 66600fac7a98 ("net: stmmac: TSO: Fix unbalanced DMA map/unmap for non-paged SKB data") moved the assignment of tx_skbuff_dma[]'s members to be later in stmmac_tso_xmit(). The buf (dma cookie) and len stored in this structure are passed to dma_unmap_single() by stmmac_tx_clean(). The DMA API requires that the dma cookie passed to dma_unmap_single() is the same as the value returned from dma_map_single(). However, by moving the assignment later, this is not the case when priv->dma_cap.addr64 > 32 as "des" is offset by proto_hdr_len. This causes problems such as: dwc-eth-dwmac 2490000.ethernet eth0: Tx DMA map failed and with DMA_API_DEBUG enabled: DMA-API: dwc-eth-dwmac 2490000.ethernet: device driver tries to +free DMA memory it has not allocated [device address=0x000000ffffcf65c0] [size=66 bytes] Fix this by maintaining "des" as the original DMA cookie, and use tso_des to pass the offset DMA cookie to stmmac_tso_allocator(). Full details of the crashes can be found at: https://lore.kernel.org/all/d8112193-0386-4e14-b516-37c2d838171a@nvidia.com/ https://lore.kernel.org/all/klkzp5yn5kq5efgtrow6wbvnc46bcqfxs65nz3qy77ujr5turc@bwwhelz2l4dw/ | |||||
| CVE-2024-56720 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: bpf, sockmap: Several fixes to bpf_msg_pop_data Several fixes to bpf_msg_pop_data, 1. In sk_msg_shift_left, we should put_page 2. if (len == 0), return early is better 3. pop the entire sk_msg (last == msg->sg.size) should be supported 4. Fix for the value of variable "a" 5. In sk_msg_shift_left, after shifting, i has already pointed to the next element. Addtional sk_msg_iter_var_next may result in BUG. | |||||
| CVE-2021-47016 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: m68k: mvme147,mvme16x: Don't wipe PCC timer config bits Don't clear the timer 1 configuration bits when clearing the interrupt flag and counter overflow. As Michael reported, "This results in no timer interrupts being delivered after the first. Initialization then hangs in calibrate_delay as the jiffies counter is not updated." On mvme16x, enable the timer after requesting the irq, consistent with mvme147. | |||||
| CVE-2021-47056 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: crypto: qat - ADF_STATUS_PF_RUNNING should be set after adf_dev_init ADF_STATUS_PF_RUNNING is (only) used and checked by adf_vf2pf_shutdown() before calling adf_iov_putmsg()->mutex_lock(vf2pf_lock), however the vf2pf_lock is initialized in adf_dev_init(), which can fail and when it fail, the vf2pf_lock is either not initialized or destroyed, a subsequent use of vf2pf_lock will cause issue. To fix this issue, only set this flag if adf_dev_init() returns 0. [ 7.178404] BUG: KASAN: user-memory-access in __mutex_lock.isra.0+0x1ac/0x7c0 [ 7.180345] Call Trace: [ 7.182576] mutex_lock+0xc9/0xd0 [ 7.183257] adf_iov_putmsg+0x118/0x1a0 [intel_qat] [ 7.183541] adf_vf2pf_shutdown+0x4d/0x7b [intel_qat] [ 7.183834] adf_dev_shutdown+0x172/0x2b0 [intel_qat] [ 7.184127] adf_probe+0x5e9/0x600 [qat_dh895xccvf] | |||||
| CVE-2021-47066 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: async_xor: increase src_offs when dropping destination page Now we support sharing one page if PAGE_SIZE is not equal stripe size. To support this, it needs to support calculating xor value with different offsets for each r5dev. One offset array is used to record those offsets. In RMW mode, parity page is used as a source page. It sets ASYNC_TX_XOR_DROP_DST before calculating xor value in ops_run_prexor5. So it needs to add src_list and src_offs at the same time. Now it only needs src_list. So the xor value which is calculated is wrong. It can cause data corruption problem. I can reproduce this problem 100% on a POWER8 machine. The steps are: mdadm -CR /dev/md0 -l5 -n3 /dev/sdb1 /dev/sdc1 /dev/sdd1 --size=3G mkfs.xfs /dev/md0 mount /dev/md0 /mnt/test mount: /mnt/test: mount(2) system call failed: Structure needs cleaning. | |||||
| CVE-2021-47072 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: btrfs: fix removed dentries still existing after log is synced When we move one inode from one directory to another and both the inode and its previous parent directory were logged before, we are not supposed to have the dentry for the old parent if we have a power failure after the log is synced. Only the new dentry is supposed to exist. Generally this works correctly, however there is a scenario where this is not currently working, because the old parent of the file/directory that was moved is not authoritative for a range that includes the dir index and dir item keys of the old dentry. This case is better explained with the following example and reproducer: # The test requires a very specific layout of keys and items in the # fs/subvolume btree to trigger the bug. So we want to make sure that # on whatever platform we are, we have the same leaf/node size. # # Currently in btrfs the node/leaf size can not be smaller than the page # size (but it can be greater than the page size). So use the largest # supported node/leaf size (64K). $ mkfs.btrfs -f -n 65536 /dev/sdc $ mount /dev/sdc /mnt # "testdir" is inode 257. $ mkdir /mnt/testdir $ chmod 755 /mnt/testdir # Create several empty files to have the directory "testdir" with its # items spread over several leaves (7 in this case). $ for ((i = 1; i <= 1200; i++)); do echo -n > /mnt/testdir/file$i done # Create our test directory "dira", inode number 1458, which gets all # its items in leaf 7. # # The BTRFS_DIR_ITEM_KEY item for inode 257 ("testdir") that points to # the entry named "dira" is in leaf 2, while the BTRFS_DIR_INDEX_KEY # item that points to that entry is in leaf 3. # # For this particular filesystem node size (64K), file count and file # names, we endup with the directory entry items from inode 257 in # leaves 2 and 3, as previously mentioned - what matters for triggering # the bug exercised by this test case is that those items are not placed # in leaf 1, they must be placed in a leaf different from the one # containing the inode item for inode 257. # # The corresponding BTRFS_DIR_ITEM_KEY and BTRFS_DIR_INDEX_KEY items for # the parent inode (257) are the following: # # item 460 key (257 DIR_ITEM 3724298081) itemoff 48344 itemsize 34 # location key (1458 INODE_ITEM 0) type DIR # transid 6 data_len 0 name_len 4 # name: dira # # and: # # item 771 key (257 DIR_INDEX 1202) itemoff 36673 itemsize 34 # location key (1458 INODE_ITEM 0) type DIR # transid 6 data_len 0 name_len 4 # name: dira $ mkdir /mnt/testdir/dira # Make sure everything done so far is durably persisted. $ sync # Now do a change to inode 257 ("testdir") that does not result in # COWing leaves 2 and 3 - the leaves that contain the directory items # pointing to inode 1458 (directory "dira"). # # Changing permissions, the owner/group, updating or adding a xattr, # etc, will not change (COW) leaves 2 and 3. So for the sake of # simplicity change the permissions of inode 257, which results in # updating its inode item and therefore change (COW) only leaf 1. $ chmod 700 /mnt/testdir # Now fsync directory inode 257. # # Since only the first leaf was changed/COWed, we log the inode item of # inode 257 and only the dentries found in the first leaf, all have a # key type of BTRFS_DIR_ITEM_KEY, and no keys of type # BTRFS_DIR_INDEX_KEY, because they sort after the former type and none # exist in the first leaf. # # We also log 3 items that represent ranges for dir items and dir # indexes for which the log is authoritative: # # 1) a key of type BTRFS_DIR_LOG_ITEM_KEY, which indicates the log is # authoritative for all BTRFS_DIR_ITEM_KEY keys that have an offset # in the range [0, 2285968570] (the offset here is th ---truncated--- | |||||
| CVE-2021-47069 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 7.0 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: ipc/mqueue, msg, sem: avoid relying on a stack reference past its expiry do_mq_timedreceive calls wq_sleep with a stack local address. The sender (do_mq_timedsend) uses this address to later call pipelined_send. This leads to a very hard to trigger race where a do_mq_timedreceive call might return and leave do_mq_timedsend to rely on an invalid address, causing the following crash: RIP: 0010:wake_q_add_safe+0x13/0x60 Call Trace: __x64_sys_mq_timedsend+0x2a9/0x490 do_syscall_64+0x80/0x680 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7f5928e40343 The race occurs as: 1. do_mq_timedreceive calls wq_sleep with the address of `struct ext_wait_queue` on function stack (aliased as `ewq_addr` here) - it holds a valid `struct ext_wait_queue *` as long as the stack has not been overwritten. 2. `ewq_addr` gets added to info->e_wait_q[RECV].list in wq_add, and do_mq_timedsend receives it via wq_get_first_waiter(info, RECV) to call __pipelined_op. 3. Sender calls __pipelined_op::smp_store_release(&this->state, STATE_READY). Here is where the race window begins. (`this` is `ewq_addr`.) 4. If the receiver wakes up now in do_mq_timedreceive::wq_sleep, it will see `state == STATE_READY` and break. 5. do_mq_timedreceive returns, and `ewq_addr` is no longer guaranteed to be a `struct ext_wait_queue *` since it was on do_mq_timedreceive's stack. (Although the address may not get overwritten until another function happens to touch it, which means it can persist around for an indefinite time.) 6. do_mq_timedsend::__pipelined_op() still believes `ewq_addr` is a `struct ext_wait_queue *`, and uses it to find a task_struct to pass to the wake_q_add_safe call. In the lucky case where nothing has overwritten `ewq_addr` yet, `ewq_addr->task` is the right task_struct. In the unlucky case, __pipelined_op::wake_q_add_safe gets handed a bogus address as the receiver's task_struct causing the crash. do_mq_timedsend::__pipelined_op() should not dereference `this` after setting STATE_READY, as the receiver counterpart is now free to return. Change __pipelined_op to call wake_q_add_safe on the receiver's task_struct returned by get_task_struct, instead of dereferencing `this` which sits on the receiver's stack. As Manfred pointed out, the race potentially also exists in ipc/msg.c::expunge_all and ipc/sem.c::wake_up_sem_queue_prepare. Fix those in the same way. | |||||
| CVE-2024-49998 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 4.7 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: net: dsa: improve shutdown sequence Alexander Sverdlin presents 2 problems during shutdown with the lan9303 driver. One is specific to lan9303 and the other just happens to reproduce there. The first problem is that lan9303 is unique among DSA drivers in that it calls dev_get_drvdata() at "arbitrary runtime" (not probe, not shutdown, not remove): phy_state_machine() -> ... -> dsa_user_phy_read() -> ds->ops->phy_read() -> lan9303_phy_read() -> chip->ops->phy_read() -> lan9303_mdio_phy_read() -> dev_get_drvdata() But we never stop the phy_state_machine(), so it may continue to run after dsa_switch_shutdown(). Our common pattern in all DSA drivers is to set drvdata to NULL to suppress the remove() method that may come afterwards. But in this case it will result in an NPD. The second problem is that the way in which we set dp->conduit->dsa_ptr = NULL; is concurrent with receive packet processing. dsa_switch_rcv() checks once whether dev->dsa_ptr is NULL, but afterwards, rather than continuing to use that non-NULL value, dev->dsa_ptr is dereferenced again and again without NULL checks: dsa_conduit_find_user() and many other places. In between dereferences, there is no locking to ensure that what was valid once continues to be valid. Both problems have the common aspect that closing the conduit interface solves them. In the first case, dev_close(conduit) triggers the NETDEV_GOING_DOWN event in dsa_user_netdevice_event() which closes user ports as well. dsa_port_disable_rt() calls phylink_stop(), which synchronously stops the phylink state machine, and ds->ops->phy_read() will thus no longer call into the driver after this point. In the second case, dev_close(conduit) should do this, as per Documentation/networking/driver.rst: | Quiescence | ---------- | | After the ndo_stop routine has been called, the hardware must | not receive or transmit any data. All in flight packets must | be aborted. If necessary, poll or wait for completion of | any reset commands. So it should be sufficient to ensure that later, when we zeroize conduit->dsa_ptr, there will be no concurrent dsa_switch_rcv() call on this conduit. The addition of the netif_device_detach() function is to ensure that ioctls, rtnetlinks and ethtool requests on the user ports no longer propagate down to the driver - we're no longer prepared to handle them. The race condition actually did not exist when commit 0650bf52b31f ("net: dsa: be compatible with masters which unregister on shutdown") first introduced dsa_switch_shutdown(). It was created later, when we stopped unregistering the user interfaces from a bad spot, and we just replaced that sequence with a racy zeroization of conduit->dsa_ptr (one which doesn't ensure that the interfaces aren't up). | |||||
| CVE-2024-56769 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: media: dvb-frontends: dib3000mb: fix uninit-value in dib3000_write_reg Syzbot reports [1] an uninitialized value issue found by KMSAN in dib3000_read_reg(). Local u8 rb[2] is used in i2c_transfer() as a read buffer; in case that call fails, the buffer may end up with some undefined values. Since no elaborate error handling is expected in dib3000_write_reg(), simply zero out rb buffer to mitigate the problem. [1] Syzkaller report dvb-usb: bulk message failed: -22 (6/0) ===================================================== BUG: KMSAN: uninit-value in dib3000mb_attach+0x2d8/0x3c0 drivers/media/dvb-frontends/dib3000mb.c:758 dib3000mb_attach+0x2d8/0x3c0 drivers/media/dvb-frontends/dib3000mb.c:758 dibusb_dib3000mb_frontend_attach+0x155/0x2f0 drivers/media/usb/dvb-usb/dibusb-mb.c:31 dvb_usb_adapter_frontend_init+0xed/0x9a0 drivers/media/usb/dvb-usb/dvb-usb-dvb.c:290 dvb_usb_adapter_init drivers/media/usb/dvb-usb/dvb-usb-init.c:90 [inline] dvb_usb_init drivers/media/usb/dvb-usb/dvb-usb-init.c:186 [inline] dvb_usb_device_init+0x25a8/0x3760 drivers/media/usb/dvb-usb/dvb-usb-init.c:310 dibusb_probe+0x46/0x250 drivers/media/usb/dvb-usb/dibusb-mb.c:110 ... Local variable rb created at: dib3000_read_reg+0x86/0x4e0 drivers/media/dvb-frontends/dib3000mb.c:54 dib3000mb_attach+0x123/0x3c0 drivers/media/dvb-frontends/dib3000mb.c:758 ... | |||||
| CVE-2024-56763 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: tracing: Prevent bad count for tracing_cpumask_write If a large count is provided, it will trigger a warning in bitmap_parse_user. Also check zero for it. | |||||
| CVE-2024-56588 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: scsi: hisi_sas: Create all dump files during debugfs initialization For the current debugfs of hisi_sas, after user triggers dump, the driver allocate memory space to save the register information and create debugfs files to display the saved information. In this process, the debugfs files created after each dump. Therefore, when the dump is triggered while the driver is unbind, the following hang occurs: [67840.853907] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a0 [67840.862947] Mem abort info: [67840.865855] ESR = 0x0000000096000004 [67840.869713] EC = 0x25: DABT (current EL), IL = 32 bits [67840.875125] SET = 0, FnV = 0 [67840.878291] EA = 0, S1PTW = 0 [67840.881545] FSC = 0x04: level 0 translation fault [67840.886528] Data abort info: [67840.889524] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [67840.895117] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [67840.900284] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [67840.905709] user pgtable: 4k pages, 48-bit VAs, pgdp=0000002803a1f000 [67840.912263] [00000000000000a0] pgd=0000000000000000, p4d=0000000000000000 [67840.919177] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP [67840.996435] pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [67841.003628] pc : down_write+0x30/0x98 [67841.007546] lr : start_creating.part.0+0x60/0x198 [67841.012495] sp : ffff8000b979ba20 [67841.016046] x29: ffff8000b979ba20 x28: 0000000000000010 x27: 0000000000024b40 [67841.023412] x26: 0000000000000012 x25: ffff20202b355ae8 x24: ffff20202b35a8c8 [67841.030779] x23: ffffa36877928208 x22: ffffa368b4972240 x21: ffff8000b979bb18 [67841.038147] x20: ffff00281dc1e3c0 x19: fffffffffffffffe x18: 0000000000000020 [67841.045515] x17: 0000000000000000 x16: ffffa368b128a530 x15: ffffffffffffffff [67841.052888] x14: ffff8000b979bc18 x13: ffffffffffffffff x12: ffff8000b979bb18 [67841.060263] x11: 0000000000000000 x10: 0000000000000000 x9 : ffffa368b1289b18 [67841.067640] x8 : 0000000000000012 x7 : 0000000000000000 x6 : 00000000000003a9 [67841.075014] x5 : 0000000000000000 x4 : ffff002818c5cb00 x3 : 0000000000000001 [67841.082388] x2 : 0000000000000000 x1 : ffff002818c5cb00 x0 : 00000000000000a0 [67841.089759] Call trace: [67841.092456] down_write+0x30/0x98 [67841.096017] start_creating.part.0+0x60/0x198 [67841.100613] debugfs_create_dir+0x48/0x1f8 [67841.104950] debugfs_create_files_v3_hw+0x88/0x348 [hisi_sas_v3_hw] [67841.111447] debugfs_snapshot_regs_v3_hw+0x708/0x798 [hisi_sas_v3_hw] [67841.118111] debugfs_trigger_dump_v3_hw_write+0x9c/0x120 [hisi_sas_v3_hw] [67841.125115] full_proxy_write+0x68/0xc8 [67841.129175] vfs_write+0xd8/0x3f0 [67841.132708] ksys_write+0x70/0x108 [67841.136317] __arm64_sys_write+0x24/0x38 [67841.140440] invoke_syscall+0x50/0x128 [67841.144385] el0_svc_common.constprop.0+0xc8/0xf0 [67841.149273] do_el0_svc+0x24/0x38 [67841.152773] el0_svc+0x38/0xd8 [67841.156009] el0t_64_sync_handler+0xc0/0xc8 [67841.160361] el0t_64_sync+0x1a4/0x1a8 [67841.164189] Code: b9000882 d2800002 d2800023 f9800011 (c85ffc05) [67841.170443] ---[ end trace 0000000000000000 ]--- To fix this issue, create all directories and files during debugfs initialization. In this way, the driver only needs to allocate memory space to save information each time the user triggers dumping. | |||||
| CVE-2024-50121 | 1 Linux | 1 Linux Kernel | 2025-01-09 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: nfsd: cancel nfsd_shrinker_work using sync mode in nfs4_state_shutdown_net In the normal case, when we excute `echo 0 > /proc/fs/nfsd/threads`, the function `nfs4_state_destroy_net` in `nfs4_state_shutdown_net` will release all resources related to the hashed `nfs4_client`. If the `nfsd_client_shrinker` is running concurrently, the `expire_client` function will first unhash this client and then destroy it. This can lead to the following warning. Additionally, numerous use-after-free errors may occur as well. nfsd_client_shrinker echo 0 > /proc/fs/nfsd/threads expire_client nfsd_shutdown_net unhash_client ... nfs4_state_shutdown_net /* won't wait shrinker exit */ /* cancel_work(&nn->nfsd_shrinker_work) * nfsd_file for this /* won't destroy unhashed client1 */ * client1 still alive nfs4_state_destroy_net */ nfsd_file_cache_shutdown /* trigger warning */ kmem_cache_destroy(nfsd_file_slab) kmem_cache_destroy(nfsd_file_mark_slab) /* release nfsd_file and mark */ __destroy_client ==================================================================== BUG nfsd_file (Not tainted): Objects remaining in nfsd_file on __kmem_cache_shutdown() -------------------------------------------------------------------- CPU: 4 UID: 0 PID: 764 Comm: sh Not tainted 6.12.0-rc3+ #1 dump_stack_lvl+0x53/0x70 slab_err+0xb0/0xf0 __kmem_cache_shutdown+0x15c/0x310 kmem_cache_destroy+0x66/0x160 nfsd_file_cache_shutdown+0xac/0x210 [nfsd] nfsd_destroy_serv+0x251/0x2a0 [nfsd] nfsd_svc+0x125/0x1e0 [nfsd] write_threads+0x16a/0x2a0 [nfsd] nfsctl_transaction_write+0x74/0xa0 [nfsd] vfs_write+0x1a5/0x6d0 ksys_write+0xc1/0x160 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e ==================================================================== BUG nfsd_file_mark (Tainted: G B W ): Objects remaining nfsd_file_mark on __kmem_cache_shutdown() -------------------------------------------------------------------- dump_stack_lvl+0x53/0x70 slab_err+0xb0/0xf0 __kmem_cache_shutdown+0x15c/0x310 kmem_cache_destroy+0x66/0x160 nfsd_file_cache_shutdown+0xc8/0x210 [nfsd] nfsd_destroy_serv+0x251/0x2a0 [nfsd] nfsd_svc+0x125/0x1e0 [nfsd] write_threads+0x16a/0x2a0 [nfsd] nfsctl_transaction_write+0x74/0xa0 [nfsd] vfs_write+0x1a5/0x6d0 ksys_write+0xc1/0x160 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e To resolve this issue, cancel `nfsd_shrinker_work` using synchronous mode in nfs4_state_shutdown_net. | |||||