Total
222 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2018-15390 | 1 Cisco | 1 Firepower Threat Defense | 2020-08-31 | 7.1 HIGH | 6.8 MEDIUM |
| A vulnerability in the FTP inspection engine of Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability exists because the affected software fails to release spinlocks when a device is running low on system memory, if the software is configured to apply FTP inspection and an access control rule to transit traffic, and the access control rule is associated with an FTP file policy. An attacker could exploit this vulnerability by sending a high rate of transit traffic through an affected device to cause a low-memory condition on the device. A successful exploit could allow the attacker to cause a software panic on the affected device, which could cause the device to reload and result in a temporary DoS condition. | |||||
| CVE-2020-3179 | 1 Cisco | 25 Asa 5505, Asa 5505 Firmware, Asa 5510 and 22 more | 2020-05-12 | 7.8 HIGH | 7.5 HIGH |
| A vulnerability in the generic routing encapsulation (GRE) tunnel decapsulation feature of Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to a memory handling error when GRE over IPv6 traffic is processed. An attacker could exploit this vulnerability by sending crafted GRE over IPv6 packets with either IPv4 or IPv6 payload through an affected device. A successful exploit could allow the attacker to cause the device to crash, resulting in a DoS condition. | |||||
| CVE-2020-3253 | 1 Cisco | 1 Firepower Threat Defense | 2020-05-12 | 7.2 HIGH | 6.7 MEDIUM |
| A vulnerability in the support tunnel feature of Cisco Firepower Threat Defense (FTD) Software could allow an authenticated, local attacker to access the shell of an affected device even though expert mode is disabled. The vulnerability is due to improper configuration of the support tunnel feature. An attacker could exploit this vulnerability by enabling the support tunnel, setting a key, and deriving the tunnel password. A successful exploit could allow the attacker to run any system command with root access on an affected device. | |||||
| CVE-2020-3255 | 1 Cisco | 25 Asa 5505, Asa 5505 Firmware, Asa 5510 and 22 more | 2020-05-12 | 5.0 MEDIUM | 7.5 HIGH |
| A vulnerability in the packet processing functionality of Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to inefficient memory management. An attacker could exploit this vulnerability by sending a high rate of IPv4 or IPv6 traffic through an affected device. This traffic would need to match a configured block action in an access control policy. An exploit could allow the attacker to cause a memory exhaustion condition on the affected device, which would result in a DoS for traffic transiting the device, as well as sluggish performance of the management interface. Once the flood is stopped, performance should return to previous states. | |||||
| CVE-2019-12694 | 1 Cisco | 1 Firepower Threat Defense | 2019-10-10 | 7.2 HIGH | 6.7 MEDIUM |
| A vulnerability in the command line interface (CLI) of Cisco Firepower Threat Defense (FTD) Software could allow an authenticated, local attacker with administrative privileges to execute commands on the underlying operating system with root privileges. The vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by executing a specific CLI command that includes crafted arguments. A successful exploit could allow the attacker to execute commands on the underlying OS with root privileges. | |||||
| CVE-2019-1704 | 1 Cisco | 1 Firepower Threat Defense | 2019-10-09 | 5.0 MEDIUM | 7.5 HIGH |
| Multiple vulnerabilities in the Server Message Block (SMB) Protocol preprocessor detection engine for Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, adjacent or remote attacker to cause a denial of service (DoS) condition. For more information about these vulnerabilities, see the Details section of this advisory. | |||||
| CVE-2019-1715 | 1 Cisco | 11 Adaptive Security Appliance Device Manager, Asa-5506-x, Asa-5506h-x and 8 more | 2019-10-09 | 5.0 MEDIUM | 7.5 HIGH |
| A vulnerability in the Deterministic Random Bit Generator (DRBG), also known as Pseudorandom Number Generator (PRNG), used in Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a cryptographic collision, enabling the attacker to discover the private key of an affected device. The vulnerability is due to insufficient entropy in the DRBG when generating cryptographic keys. An attacker could exploit this vulnerability by generating a large number of cryptographic keys on an affected device and looking for collisions with target devices. A successful exploit could allow the attacker to impersonate an affected target device or to decrypt traffic secured by an affected key that is sent to or from an affected target device. | |||||
| CVE-2019-1669 | 1 Cisco | 1 Firepower Threat Defense | 2019-10-09 | 5.0 MEDIUM | 8.6 HIGH |
| A vulnerability in the data acquisition (DAQ) component of Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to bypass configured access control policies or cause a denial of service (DoS) condition. The vulnerability exists because the affected software improperly manages system memory resources when inspecting traffic. An attacker could exploit this vulnerability by generating specific traffic patterns for the software to inspect. A successful exploit could allow the attacker to exhaust system memory resources used for traffic inspection. Depending on the configuration, the FTD Software could fail open and cease to inspect traffic or fail closed and result in a DoS condition. This vulnerability may require manual intervention to restore the software. | |||||
| CVE-2019-12675 | 1 Cisco | 17 Firepower 4110, Firepower 4110 Firmware, Firepower 4115 and 14 more | 2019-10-09 | 7.2 HIGH | 8.8 HIGH |
| Multiple vulnerabilities in the multi-instance feature of Cisco Firepower Threat Defense (FTD) Software could allow an authenticated, local attacker to escape the container for their FTD instance and execute commands with root privileges in the host namespace. These vulnerabilities are due to insufficient protections on the underlying filesystem. An attacker could exploit these vulnerabilities by modifying critical files on the underlying filesystem. A successful exploit could allow the attacker to execute commands with root privileges within the host namespace. This could allow the attacker to impact other running FTD instances. | |||||
| CVE-2019-12674 | 1 Cisco | 17 Firepower 4110, Firepower 4110 Firmware, Firepower 4115 and 14 more | 2019-10-09 | 7.2 HIGH | 8.2 HIGH |
| Multiple vulnerabilities in the multi-instance feature of Cisco Firepower Threat Defense (FTD) Software could allow an authenticated, local attacker to escape the container for their FTD instance and execute commands with root privileges in the host namespace. These vulnerabilities are due to insufficient protections on the underlying filesystem. An attacker could exploit these vulnerabilities by modifying critical files on the underlying filesystem. A successful exploit could allow the attacker to execute commands with root privileges within the host namespace. This could allow the attacker to impact other running FTD instances. | |||||
| CVE-2018-0453 | 1 Cisco | 1 Firepower Threat Defense | 2019-10-09 | 7.2 HIGH | 8.2 HIGH |
| A vulnerability in the Sourcefire tunnel control channel protocol in Cisco Firepower System Software running on Cisco Firepower Threat Defense (FTD) sensors could allow an authenticated, local attacker to execute specific CLI commands with root privileges on the Cisco Firepower Management Center (FMC), or through Cisco FMC on other Firepower sensors and devices that are controlled by the same Cisco FMC. To send the commands, the attacker must have root privileges for at least one affected sensor or the Cisco FMC. The vulnerability exists because the affected software performs insufficient checks for certain CLI commands, if the commands are executed via a Sourcefire tunnel connection. An attacker could exploit this vulnerability by authenticating with root privileges to a Firepower sensor or Cisco FMC, and then sending specific CLI commands to the Cisco FMC or through the Cisco FMC to another Firepower sensor via the Sourcefire tunnel connection. A successful exploit could allow the attacker to modify device configurations or delete files on the device that is running Cisco FMC Software or on any Firepower device that is managed by Cisco FMC. | |||||
| CVE-2018-0254 | 1 Cisco | 31 Amp 7150, Amp 8150, Firepower Appliance 7010 and 28 more | 2019-10-09 | 5.0 MEDIUM | 5.3 MEDIUM |
| A vulnerability in the detection engine of Cisco Firepower System Software could allow an unauthenticated, remote attacker to bypass configured file action policies if an Intelligent Application Bypass (IAB) with a drop percentage threshold is also configured. The vulnerability is due to incorrect counting of the percentage of dropped traffic. An attacker could exploit this vulnerability by sending network traffic to a targeted device. An exploit could allow the attacker to bypass configured file action policies, and traffic that should be dropped could be allowed into the network. Cisco Bug IDs: CSCvf86435. | |||||
| CVE-2018-0138 | 1 Cisco | 1 Firepower Threat Defense | 2019-10-09 | 5.0 MEDIUM | 5.3 MEDIUM |
| A vulnerability in the detection engine of Cisco Firepower System Software could allow an unauthenticated, remote attacker to bypass file policies that are configured to block files transmitted to an affected device via the BitTorrent protocol. The vulnerability exists because the affected software does not detect BitTorrent handshake messages correctly. An attacker could exploit this vulnerability by sending a crafted BitTorrent connection request to an affected device. A successful exploit could allow the attacker to bypass file policies that are configured to block files transmitted to the affected device via the BitTorrent protocol. Cisco Bug IDs: CSCve26946. | |||||
| CVE-2018-0244 | 1 Cisco | 1 Firepower Threat Defense | 2019-10-09 | 5.0 MEDIUM | 5.8 MEDIUM |
| A vulnerability in the detection engine of Cisco Firepower System Software could allow an unauthenticated, remote attacker to bypass a configured file action policy to drop the Server Message Block (SMB) protocol if a malware file is detected. The vulnerability is due to how the SMB protocol handles a case in which a large file transfer fails. This case occurs when some pieces of the file are successfully transferred to the remote endpoint, but ultimately the file transfer fails and is reset. An attacker could exploit this vulnerability by sending a crafted SMB file transfer request through the targeted device. An exploit could allow the attacker to pass an SMB file that contains malware, which the device is configured to block. This vulnerability affects Cisco Firepower System Software when one or more file action policies are configured, on software releases prior to 6.2.3. Cisco Bug IDs: CSCvc20141. | |||||
| CVE-2018-0297 | 1 Cisco | 1 Firepower Threat Defense | 2019-10-09 | 5.0 MEDIUM | 5.8 MEDIUM |
| A vulnerability in the detection engine of Cisco Firepower Threat Defense software could allow an unauthenticated, remote attacker to bypass a configured Secure Sockets Layer (SSL) Access Control (AC) policy to block SSL traffic. The vulnerability is due to the incorrect handling of TCP SSL packets received out of order. An attacker could exploit this vulnerability by sending a crafted SSL connection through the affected device. A successful exploit could allow the attacker to bypass a configured SSL AC policy to block SSL traffic. Cisco Bug IDs: CSCvg09316. | |||||
| CVE-2018-0243 | 1 Cisco | 1 Firepower Threat Defense | 2019-10-09 | 5.0 MEDIUM | 5.8 MEDIUM |
| A vulnerability in the detection engine of Cisco Firepower System Software could allow an unauthenticated, remote attacker to bypass a configured file action policy that is intended to drop the Server Message Block Version 2 (SMB2) and SMB Version 3 (SMB3) protocols if malware is detected. The vulnerability is due to incorrect detection of an SMB2 or SMB3 file based on the total file length. An attacker could exploit this vulnerability by sending a crafted SMB2 or SMB3 transfer request through the targeted device. An exploit could allow the attacker to pass SMB2 or SMB3 files that could be malware even though the device is configured to block them. This vulnerability does not exist for SMB Version 1 (SMB1) files. This vulnerability affects Cisco Firepower System Software when one or more file action policies are configured, on software releases prior to 6.2.3. Cisco Bug IDs: CSCvg68807. | |||||
| CVE-2017-6632 | 1 Cisco | 1 Firepower Threat Defense | 2019-10-09 | 7.8 HIGH | 7.5 HIGH |
| A vulnerability in the logging configuration of Secure Sockets Layer (SSL) policies for Cisco FirePOWER System Software 5.3.0 through 6.2.2 could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition due to high consumption of system resources. The vulnerability is due to the logging of certain TCP packets by the affected software. An attacker could exploit this vulnerability by sending a flood of crafted TCP packets to an affected device. A successful exploit could allow the attacker to cause a DoS condition. The success of an exploit is dependent on how an administrator has configured logging for SSL policies for a device. This vulnerability affects Cisco FirePOWER System Software that is configured to log connections by using SSL policy default actions. Cisco Bug IDs: CSCvd07072. | |||||
| CVE-2017-6625 | 1 Cisco | 1 Firepower Threat Defense | 2019-10-09 | 5.5 MEDIUM | 7.1 HIGH |
| A "Cisco Firepower Threat Defense 6.0.0 through 6.2.2 and Cisco ASA with FirePOWER Module Denial of Service" vulnerability in the access control policy of Cisco Firepower System Software could allow an authenticated, remote attacker to cause an affected system to stop inspecting and processing packets, resulting in a denial of service (DoS) condition. The vulnerability is due to improper SSL policy handling by the affected software when packets are passed through the sensing interfaces of an affected system. An attacker could exploit this vulnerability by sending crafted packets through a targeted system. This vulnerability affects Cisco Firepower System Software that is configured with the SSL policy feature. Cisco Bug IDs: CSCvc84361. | |||||
| CVE-2018-15462 | 1 Cisco | 1 Firepower Threat Defense | 2019-10-03 | 7.8 HIGH | 7.5 HIGH |
| A vulnerability in the TCP ingress handler for the data interfaces that are configured with management access to Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause an increase in CPU and memory usage, resulting in a denial of service (DoS) condition. The vulnerability is due to insufficient ingress TCP rate limiting for TCP ports 22 (SSH) and 443 (HTTPS). An attacker could exploit this vulnerability by sending a crafted, steady stream of TCP traffic to port 22 or 443 on the data interfaces that are configured with management access to the affected device. | |||||
| CVE-2017-3887 | 1 Cisco | 1 Firepower Threat Defense | 2019-10-03 | 4.3 MEDIUM | 5.9 MEDIUM |
| A vulnerability in the detection engine that handles Secure Sockets Layer (SSL) packets for Cisco Firepower System Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition because the Snort process unexpectedly restarts. This vulnerability affects Cisco Firepower System Software prior to the first fixed release when it is configured with an SSL Decrypt-Resign policy. More Information: CSCvb62292. Known Affected Releases: 6.0.1 6.1.0 6.2.0. Known Fixed Releases: 6.2.0 6.1.0.2. | |||||