Filtered by vendor Juniper
Subscribe
Total
894 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2023-28968 | 1 Juniper | 31 Appid Service Sigpack, Jdpi-decoder Engine, Junos and 28 more | 2023-04-27 | N/A | 5.3 MEDIUM |
| An Improperly Controlled Sequential Memory Allocation vulnerability in the Juniper Networks Deep Packet Inspection-Decoder (JDPI-Decoder) Application Signature component of Junos OS's AppID service on SRX Series devices will stop the JDPI-Decoder from identifying dynamic application traffic, allowing an unauthenticated network-based attacker to send traffic to the target device using the JDPI-Decoder, designed to inspect dynamic application traffic and take action upon this traffic, to instead begin to not take action and to pass the traffic through. An example session can be seen by running the following command and evaluating the output. user@device# run show security flow session source-prefix <address/mask> extensive Session ID: <session ID>, Status: Normal, State: Active Policy name: <name of policy> Dynamic application: junos:UNKNOWN, <<<<< LOOK HERE Please note, the JDPI-Decoder and the AppID SigPack are both affected and both must be upgraded along with the operating system to address the matter. By default, none of this is auto-enabled for automatic updates. This issue affects: Juniper Networks any version of the JDPI-Decoder Engine prior to version 5.7.0-47 with the JDPI-Decoder enabled using any version of the AppID SigPack prior to version 1.550.2-31 (SigPack 3533) on Junos OS on SRX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S11; 20.1 version 20.1R1 and later versions prior to 20.2R3-S7; 20.3 version 20.3R1 and later versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S3; 22.1 versions prior to 22.1R3-S1; 22.2 versions prior to 22.2R2-S1, 22.2R3; 22.3 versions prior to 22.3R1-S2, 22.3R2; | |||||
| CVE-2023-28967 | 1 Juniper | 2 Junos, Junos Os Evolved | 2023-04-27 | N/A | 7.5 HIGH |
| A Use of Uninitialized Resource vulnerability in the Border Gateway Protocol (BGP) software of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker to send specific genuine BGP packets to a device configured with BGP to cause a Denial of Service (DoS) by crashing the Routing Protocol Daemon (rpd). This issue is triggered when the packets attempt to initiate a BGP connection before a BGP session is successfully established. Continued receipt of these specific BGP packets will cause a sustained Denial of Service condition. This issue is triggerable in both iBGP and eBGP deployments. This issue affects: Juniper Networks Junos OS 21.1 version 21.1R1 and later versions prior to 21.1R3-S5; 21.2 version 21.2R1 and later versions prior to 21.2R3-S2; 21.3 version 21.3R1 and later versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 21.1R1. This issue affects: Juniper Networks Junos OS Evolved 21.1-EVO version 21.1R1-EVO and later versions prior to 21.4R3-EVO; 22.1-EVO versions prior to 22.1R3-EVO; 22.2-EVO versions prior to 22.2R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 21.1R1-EVO. | |||||
| CVE-2023-28965 | 1 Juniper | 2 Junos, Qfx10002 | 2023-04-27 | N/A | 7.5 HIGH |
| An Improper Check or Handling of Exceptional Conditions within the storm control feature of Juniper Networks Junos OS allows an attacker sending a high rate of traffic to cause a Denial of Service. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. Storm control monitors the level of applicable incoming traffic and compares it with the level specified. If the combined level of the applicable traffic exceeds the specified level, the switch drops packets for the controlled traffic types. This issue affects Juniper Networks Junos OS on QFX10002: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2. | |||||
| CVE-2023-28966 | 1 Juniper | 1 Junos Os Evolved | 2023-04-27 | N/A | 7.8 HIGH |
| An Incorrect Default Permissions vulnerability in Juniper Networks Junos OS Evolved allows a low-privileged local attacker with shell access to modify existing files or execute commands as root. The issue is caused by improper file and directory permissions on certain system files, allowing an attacker with access to these files and folders to inject CLI commands as root. This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R3-S5-EVO; 21.2 versions prior to 21.2R3-EVO; 21.3 versions prior to 21.3R2-EVO. | |||||
| CVE-2023-28964 | 1 Juniper | 2 Junos, Junos Os Evolved | 2023-04-27 | N/A | 7.5 HIGH |
| An Improper Handling of Length Parameter Inconsistency vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network based, unauthenticated attacker to cause an RPD crash leading to a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Upon receipt of a malformed BGP flowspec update, RPD will crash resulting in a Denial of Service. This issue affects Juniper Networks Junos OS: All versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S1, 20.3R2; Juniper Networks Junos OS Evolved: All versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R2-EVO; 20.3 versions prior to 20.3R2-EVO; | |||||
| CVE-2023-28963 | 1 Juniper | 1 Junos | 2023-04-27 | N/A | 5.3 MEDIUM |
| An Improper Authentication vulnerability in cert-mgmt.php, used by the J-Web component of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to read arbitrary files from temporary folders on the device. This issue affects Juniper Networks Junos OS: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S11; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S7; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S3; 22.1 versions prior to 22.1R3-S1; 22.2 versions prior to 22.2R2-S1, 22.2R3; 22.3 versions prior to 22.3R1-S2, 22.3R2. | |||||
| CVE-2023-1697 | 1 Juniper | 6 Junos, Ptx1000, Qfx10000 and 3 more | 2023-04-26 | N/A | 6.5 MEDIUM |
| An Improper Handling of Missing Values vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker to cause a dcpfe process core and thereby a Denial of Service (DoS). Continued receipt of these specific frames will cause a sustained Denial of Service condition. This issue occurs when a specific malformed ethernet frame is received. This issue affects Juniper Networks Junos OS on QFX10000 Series, PTX1000 Series Series: All versions prior to 19.4R3-S10; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S1; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2. | |||||
| CVE-2017-10616 | 1 Juniper | 1 Contrail | 2023-03-24 | 6.4 MEDIUM | 5.3 MEDIUM |
| The ifmap service that comes bundled with Juniper Networks Contrail releases uses hard coded credentials. Affected releases are Contrail releases 2.2 prior to 2.21.4; 3.0 prior to 3.0.3.4; 3.1 prior to 3.1.4.0; 3.2 prior to 3.2.5.0. CVE-2017-10616 and CVE-2017-10617 can be chained together and have a combined CVSSv3 score of 5.8 (CVSS:3.0/AV:N/AC:L/PR:N/UI:N/S:C/C:L/I:N/A:N). | |||||
| CVE-2019-0053 | 2 Debian, Juniper | 2 Debian Linux, Junos | 2023-03-23 | 4.6 MEDIUM | 7.8 HIGH |
| Insufficient validation of environment variables in the telnet client supplied in Junos OS can lead to stack-based buffer overflows, which can be exploited to bypass veriexec restrictions on Junos OS. A stack-based overflow is present in the handling of environment variables when connecting via the telnet client to remote telnet servers. This issue only affects the telnet client — accessible from the CLI or shell — in Junos OS. Inbound telnet services are not affected by this issue. This issue affects: Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S13; 12.3X48 versions prior to 12.3X48-D80; 14.1X53 versions prior to 14.1X53-D130, 14.1X53-D49; 15.1 versions prior to 15.1F6-S12, 15.1R7-S4; 15.1X49 versions prior to 15.1X49-D170; 15.1X53 versions prior to 15.1X53-D237, 15.1X53-D496, 15.1X53-D591, 15.1X53-D69; 16.1 versions prior to 16.1R3-S11, 16.1R7-S4; 16.2 versions prior to 16.2R2-S9; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R1-S8, 17.2R2-S7, 17.2R3-S1; 17.3 versions prior to 17.3R3-S4; 17.4 versions prior to 17.4R1-S6, 17.4R2-S3, 17.4R3; 18.1 versions prior to 18.1R2-S4, 18.1R3-S3; 18.2 versions prior to 18.2R1-S5, 18.2R2-S2, 18.2R3; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R1-S3, 18.3R2; 18.4 versions prior to 18.4R1-S2, 18.4R2. | |||||
| CVE-2009-1185 | 7 Canonical, Debian, Fedoraproject and 4 more | 9 Ubuntu Linux, Debian Linux, Fedora and 6 more | 2023-02-13 | 7.2 HIGH | N/A |
| udev before 1.4.1 does not verify whether a NETLINK message originates from kernel space, which allows local users to gain privileges by sending a NETLINK message from user space. | |||||
| CVE-2015-3209 | 8 Arista, Canonical, Debian and 5 more | 19 Eos, Ubuntu Linux, Debian Linux and 16 more | 2023-02-13 | 7.5 HIGH | N/A |
| Heap-based buffer overflow in the PCNET controller in QEMU allows remote attackers to execute arbitrary code by sending a packet with TXSTATUS_STARTPACKET set and then a crafted packet with TXSTATUS_DEVICEOWNS set. | |||||
| CVE-2023-22404 | 1 Juniper | 46 Junos, Mx10, Mx10000 and 43 more | 2023-02-03 | N/A | 6.5 MEDIUM |
| An Out-of-bounds Write vulnerability in the Internet Key Exchange Protocol daemon (iked) of Juniper Networks Junos OS on SRX series and MX with SPC3 allows an authenticated, network-based attacker to cause a Denial of Service (DoS). iked will crash and restart, and the tunnel will not come up when a peer sends a specifically formatted payload during the negotiation. This will impact other IKE negotiations happening at the same time. Continued receipt of this specifically formatted payload will lead to continuous crashing of iked and thereby the inability for any IKE negotiations to take place. Note that this payload is only processed after the authentication has successfully completed. So the issue can only be exploited by an attacker who can successfully authenticate. This issue affects Juniper Networks Junos OS on SRX Series, and MX Series with SPC3: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2. | |||||
| CVE-2023-22405 | 1 Juniper | 15 Ex4600, Ex4600-vc, Ex4650 and 12 more | 2023-02-03 | N/A | 6.5 MEDIUM |
| An Improper Preservation of Consistency Between Independent Representations of Shared State vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker to cause a Denial of Service (DoS) to device due to out of resources. When a device is configured with "service-provider/SP style" switching, and mac-limiting is configured on an Aggregated Ethernet (ae) interface, and then a PFE is restarted or the device is rebooted, mac-limiting doesn't work anymore. Please note that the issue might not be apparent as traffic will continue to flow through the device although the mac table and respective logs will indicate that mac limit is reached. Functionality can be restored by removing and re-adding the MAC limit configuration. This issue affects Juniper Networks Junos OS on QFX5k Series, EX46xx Series: All versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3 on; 21.4 versions prior to 21.4R3 on; 22.1 versions prior to 22.1R2 on. | |||||
| CVE-2022-22187 | 1 Juniper | 1 Identity Management Service | 2023-01-31 | 7.2 HIGH | 7.8 HIGH |
| An Improper Privilege Management vulnerability in the Windows Installer framework used in the Juniper Networks Juniper Identity Management Service (JIMS) allows an unprivileged user to trigger a repair operation. Running a repair operation, in turn, will trigger a number of file operations in the %TEMP% folder of the user triggering the repair. Some of these operations will be performed from a SYSTEM context (started via the Windows Installer service), including the execution of temporary files. An attacker may be able to provide malicious binaries to the Windows Installer, which will be executed with high privilege, leading to a local privilege escalation. This issue affects Juniper Networks Juniper Identity Management Service (JIMS) versions prior to 1.4.0. | |||||
| CVE-2017-10617 | 1 Juniper | 1 Contrail | 2023-01-30 | 5.0 MEDIUM | 5.0 MEDIUM |
| The ifmap service that comes bundled with Contrail has an XML External Entity (XXE) vulnerability that may allow an attacker to retrieve sensitive system files. Affected releases are Juniper Networks Contrail 2.2 prior to 2.21.4; 3.0 prior to 3.0.3.4; 3.1 prior to 3.1.4.0; 3.2 prior to 3.2.5.0. CVE-2017-10616 and CVE-2017-10617 can be chained together and have a combined CVSSv3 score of 5.8 (AV:N/AC:L/PR:N/UI:N/S:C/C:L/I:N/A:N). | |||||
| CVE-2023-22400 | 1 Juniper | 1 Junos Os Evolved | 2023-01-24 | N/A | 7.5 HIGH |
| An Uncontrolled Resource Consumption vulnerability in the PFE management daemon (evo-pfemand) of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to cause an FPC crash leading to a Denial of Service (DoS). When a specific SNMP GET operation or a specific CLI command is executed this will cause a GUID resource leak, eventually leading to exhaustion and result in an FPC crash and reboot. GUID exhaustion will trigger a syslog message like one of the following for example: evo-pfemand[<pid>]: get_next_guid: Ran out of Guid Space ... evo-aftmand-zx[<pid>]: get_next_guid: Ran out of Guid Space ... This leak can be monitored by running the following command and taking note of the value in the rightmost column labeled Guids: user@host> show platform application-info allocations app evo-pfemand | match "IFDId|IFLId|Context" Node Application Context Name Live Allocs Fails Guids re0 evo-pfemand net::juniper::interfaces::IFDId 0 3448 0 3448 re0 evo-pfemand net::juniper::interfaces::IFLId 0 561 0 561 user@host> show platform application-info allocations app evo-pfemand | match "IFDId|IFLId|Context" Node Application Context Name Live Allocs Fails Guids re0 evo-pfemand net::juniper::interfaces::IFDId 0 3784 0 3784 re0 evo-pfemand net::juniper::interfaces::IFLId 0 647 0 647 This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R3-S3-EVO; 21.1-EVO version 21.1R1-EVO and later versions; 21.2-EVO versions prior to 21.2R3-S4-EVO; 21.3-EVO version 21.3R1-EVO and later versions; 21.4-EVO versions prior to 21.4R2-EVO. | |||||
| CVE-2023-22399 | 1 Juniper | 1 Junos | 2023-01-24 | N/A | 7.5 HIGH |
| When sFlow is enabled and it monitors a packet forwarded via ECMP, a buffer management vulnerability in the dcpfe process of Juniper Networks Junos OS on QFX10K Series systems allows an attacker to cause the Packet Forwarding Engine (PFE) to crash and restart by sending specific genuine packets to the device, resulting in a Denial of Service (DoS) condition. The dcpfe process tries to copy more data into a smaller buffer, which overflows and corrupts the buffer, causing a crash of the dcpfe process. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on QFX10K Series: All versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R2-S2, 21.4R3; 22.1 versions prior to 22.1R2; 22.2 versions prior to 22.2R1-S2, 22.2R2. | |||||
| CVE-2023-22398 | 1 Juniper | 2 Junos, Junos Os Evolved | 2023-01-24 | N/A | 5.5 MEDIUM |
| An Access of Uninitialized Pointer vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a locally authenticated attacker with low privileges to cause a Denial of Service (DoS). When an MPLS ping is performed on BGP LSPs, the RPD might crash. Repeated execution of this operation will lead to a sustained DoS. This issue affects: Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S12; 19.1 versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R1-S9, 19.2R3-S5; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R2-S7, 19.4R3-S8; 20.1 versions prior to 20.1R3-S4; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R1-S1, 21.1R2; Juniper Networks Junos OS Evolved: All versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R2-EVO. | |||||
| CVE-2023-22397 | 1 Juniper | 2 Junos Os Evolved, Ptx10003 | 2023-01-24 | N/A | 6.1 MEDIUM |
| An Allocation of Resources Without Limits or Throttling weakness in the memory management of the Packet Forwarding Engine (PFE) on Juniper Networks Junos OS Evolved PTX10003 Series devices allows an adjacently located attacker who has established certain preconditions and knowledge of the environment to send certain specific genuine packets to begin a Time-of-check Time-of-use (TOCTOU) Race Condition attack which will cause a memory leak to begin. Once this condition begins, and as long as the attacker is able to sustain the offending traffic, a Distributed Denial of Service (DDoS) event occurs. As a DDoS event, the offending packets sent by the attacker will continue to flow from one device to another as long as they are received and processed by any devices, ultimately causing a cascading outage to any vulnerable devices. Devices not vulnerable to the memory leak will process and forward the offending packet(s) to neighboring devices. Due to internal anti-flood security controls and mechanisms reaching their maximum limit of response in the worst-case scenario, all affected Junos OS Evolved devices will reboot in as little as 1.5 days. Reboots to restore services cannot be avoided once the memory leak begins. The device will self-recover after crashing and rebooting. Operator intervention isn't required to restart the device. This issue affects: Juniper Networks Junos OS Evolved on PTX10003: All versions prior to 20.4R3-S4-EVO; 21.3 versions prior to 21.3R3-S1-EVO; 21.4 versions prior to 21.4R2-S2-EVO, 21.4R3-EVO; 22.1 versions prior to 22.1R1-S2-EVO, 22.1R2-EVO; 22.2 versions prior to 22.2R2-EVO. To check memory, customers may VTY to the PFE first then execute the following show statement: show jexpr jtm ingress-main-memory chip 255 | no-more Alternatively one may execute from the RE CLI: request pfe execute target fpc0 command "show jexpr jtm ingress-main-memory chip 255 | no-more" Iteration 1: Example output: Mem type: NH, alloc type: JTM 136776 bytes used (max 138216 bytes used) 911568 bytes available (909312 bytes from free pages) Iteration 2: Example output: Mem type: NH, alloc type: JTM 137288 bytes used (max 138216 bytes used) 911056 bytes available (909312 bytes from free pages) The same can be seen in the CLI below, assuming the scale does not change: show npu memory info Example output: FPC0:NPU16 mem-util-jnh-nh-size 2097152 FPC0:NPU16 mem-util-jnh-nh-allocated 135272 FPC0:NPU16 mem-util-jnh-nh-utilization 6 | |||||
| CVE-2023-22396 | 1 Juniper | 1 Junos | 2023-01-24 | N/A | 7.5 HIGH |
| An Uncontrolled Resource Consumption vulnerability in TCP processing on the Routing Engine (RE) of Juniper Networks Junos OS allows an unauthenticated network-based attacker to send crafted TCP packets destined to the device, resulting in an MBUF leak that ultimately leads to a Denial of Service (DoS). The system does not recover automatically and must be manually restarted to restore service. This issue occurs when crafted TCP packets are sent directly to a configured IPv4 or IPv6 interface on the device. Transit traffic will not trigger this issue. MBUF usage can be monitored through the use of the 'show system buffers' command. For example: user@junos> show system buffers | refresh 5 4054/566/4620 mbufs in use (current/cache/total) ... 4089/531/4620 mbufs in use (current/cache/total) ... 4151/589/4740 mbufs in use (current/cache/total) ... 4213/527/4740 mbufs in use (current/cache/total) This issue affects Juniper Networks Junos OS: 12.3 version 12.3R12-S19 and later versions; 15.1 version 15.1R7-S10 and later versions; 17.3 version 17.3R3-S12 and later versions; 18.4 version 18.4R3-S9 and later versions; 19.1 version 19.1R3-S7 and later versions; 19.2 version 19.2R3-S3 and later versions; 19.3 version 19.3R2-S7, 19.3R3-S3 and later versions prior to 19.3R3-S7; 19.4 version 19.4R2-S7, 19.4R3-S5 and later versions prior to 19.4R3-S10; 20.1 version 20.1R3-S1 and later versions; 20.2 version 20.2R3-S2 and later versions prior to 20.2R3-S6; 20.3 version 20.3R3-S1 and later versions prior to 20.3R3-S6; 20.4 version 20.4R2-S2, 20.4R3 and later versions prior to 20.4R3-S5; 21.1 version 21.1R2 and later versions prior to 21.1R3-S4; 21.2 version 21.2R1-S1, 21.2R2 and later versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2; 22.3 versions prior to 22.3R1-S1, 22.3R2. | |||||